How Big Should a Farm Wetland Be?
A constructed wetland is sized by the land that drains to it. Measure that catchment from LiDAR and you have the starting number for the design.
A wetland built on a farm drain or seep slows the water down, lets sediment settle and gives plants and microbes time to take out nitrogen and phosphorus. How much it removes depends mostly on one thing: how big it is compared with the land draining into it.
The Constructed Wetland Practitioners Guide from DairyNZ and NIWA (Tanner and others, 2022) sets this out for New Zealand farms. Its performance figures run from wetlands of 1% to 5% of the contributing catchment, and it quotes typical results for a wetland of 2%. As DairyNZ notes, a technical group of regional councils, government agencies and practitioners reviewed and endorsed the figures.
Wetland size by catchment
Wetland area at normal water level, not at the top of the banks:
| Land draining to it | 1% | 2% | 5% |
|---|---|---|---|
| 2 ha | 200 m² | 400 m² | 1,000 m² |
| 5 ha | 500 m² | 1,000 m² | 2,500 m² |
| 10 ha | 1,000 m² | 2,000 m² | 5,000 m² |
| 20 ha | 2,000 m² | 4,000 m² | 1 ha |
| 50 ha | 5,000 m² | 1 ha | 2.5 ha |
The guide says a well-designed wetland of 2% of its catchment typically removes 46 to 92% of the sediment from low-clay soils, 28 to 44% of the nitrogen in warm regions (22 to 33% in cool ones, such as most of the South Island) and 25 to 46% of the particulate phosphorus. Bigger wetlands remove more, up to the 5% the figures cover.
Where the figures apply
The guide is clear about the conditions behind its numbers:
- Small catchments. Up to about 50 ha, fed by drains, seeps and small streams, generally under a metre wide and 30 cm deep at normal flow.
- Flat to rolling land. Average slopes of 15° or less, with 800 to 1,600 mm of rain a year.
- Not every soil. They do not apply where most water moves through highly permeable soils as groundwater, and the sediment and phosphorus figures do not apply to clay soils (over 35% clay).
- A proper design. The figures assume a wetland built and kept as the guide describes: long and narrow (ideally 5 to 10 times longer than wide), with a deep sediment pond at the inlet of up to 20% of the wetland area, mostly shallow and densely planted, and fenced from stock.
Measure the land draining to your wetland site
Click where the drain or swale would enter the wetland and run Catchment. You get the area in hectares and the wetland size at 1%, 2% and 5%. Free to use, no login.
Open Catchment →Five steps
Find where the water gathers
Run Flow Paths and the Wetness Map over the farm. A wetland works best where a drain, swale or seep can be intercepted before it reaches a stream, often in a low corner that is already wet.
Flow Paths →Click the inflow point
Open Catchment and click where the water would enter the wetland. The point snaps to the nearest water path. Check the dark dot sits on the one you mean.
Catchment →Read the area, and the wetland size
The result gives the contributing area in hectares and, under "Using this area", the wetland at 1%, 2% and 5% of it. Try a spot a little further up or down the path to see how the size changes.
Catchment →Check the ground fits the guide
The guide’s figures are for catchments up to about 50 ha on flat to rolling land, averaging 15° or less. Slope & Aspect shows how steep the catchment is. A steep or very large catchment needs specialist advice.
Slope & Aspect →Take it to your adviser and council
Save the map as an image, or download the catchment outline with a pass. Then work through the design in the DairyNZ/NIWA guide with your farm adviser, and check consents with your regional council.
Catchment →An example: a wet corner on a dairy run-off
Illustrative, not a real farm. A farmer wants a wetland in a corner that is always wet, where a drain leaves the farm for the creek. Catchment, clicked on the drain at the corner, shows 18.6 ha draining to it. At 1% that is about 1,860 m², at 2% about 3,720 m². The corner is around 2,500 m², so it fits a wetland of between 1% and 2%. Clicking 150 m further up the drain gives 9.2 ha, where the same corner would be nearly 3%, but it would miss two paddocks of runoff. The farmer takes both options to their adviser.
Hand it on
The area, the wetland sizes and the map are free. With a pass, the catchment outline downloads as DXF, GeoJSON or KML, so the adviser, the council and the digger driver all see the same land.
What this cannot tell you
- The design. Depths, banks, outlet, spillway, plants and cost are in the DairyNZ/NIWA guide, and an experienced adviser or contractor helps.
- What drains underground. Tile drains and pipes are not in the ground model and can bring water from beyond the surface catchment.
- Your soils and climate. Clay content, groundwater and temperature all change how a wetland performs.
- Changes since the survey. The ground is as the LiDAR recorded it. New drains and earthworks are not in it.
- Consents. Ask your regional council before you dig.
Related guides
- Catchment area for a culvert or crossing — the same number, for sizing a pipe.
- Farm maps for a freshwater farm plan — the terrain maps a plan is built on.
- Critical source areas — finding the runoff a wetland could catch.
Frequently asked questions
How big should a constructed wetland be?
New Zealand guidance from DairyNZ and NIWA relates a wetland’s size to the land draining to it. Their performance figures run from wetlands of 1% to 5% of the catchment, and they quote typical results for one of 2%. So for a 10 ha catchment, that is about 1,000 m² to 5,000 m² of wetland, measured at normal water level.
What does a bigger wetland buy you?
More removal, with diminishing returns. In the guide, a well-designed wetland of 2% of its catchment typically removes 46 to 92% of sediment from low-clay soils, 28 to 44% of nitrogen in warm regions (22 to 33% in cool ones) and 25 to 46% of particulate phosphorus. The figures rise towards 5%.
How do I find the catchment area for my wetland?
Pick the spot where the drain, swale or seep would enter the wetland, then measure all the land draining to it. The Catchment tool does this from LINZ LiDAR: click the spot and it reports the area in hectares, with the wetland size at 1%, 2% and 5% next to it.
Does it work for tile drains?
Only partly. The tool measures the surface catchment from the shape of the ground. Tile drains can carry water from land outside it, and they are not in the ground model. If a wetland will mostly treat tile drain water, the drained area from your drainage plan is the better figure.
Do I need a consent to build a wetland?
You might. Digging, damming water, working near streams and natural wetlands, and fish passage can all need one, and the rules differ between regions. Talk to your regional council’s land or freshwater team early.
Is this the same as restoring a natural wetland?
No. These figures are for constructed wetlands built to treat farm runoff. Natural wetlands are protected and managed differently. Your regional council and the Department of Conservation have guidance for those.